Tag Archives: propeller shaft

China OEM CZPT OEM 2123-2201015-20 21213-2203012-1 Auto Spare Parts Propeller Half Shaft Cardan Rear Axle Reinforced Drive Shaft for Chevrolet Niva Vaz 2123 2121-21214 with high quality

Product Description

What are the symptoms of a damaged half shaft?
The half shaft is the component that transmits power to the wheels. Without the half shaft, the power cannot be transmitted to the wheels. If the car’s half shaft is damaged, it will cause the car to vibrate abnormally when driving, and will also cause abnormal noises when the car is driving. If the drive shaft is damaged, it needs to be replaced immediately.
If there is a problem with the drive shaft when the vehicle is driving at high speed, it may cause the car tires to fall off or the wheel hub to become out of round. The wheel hub out of roundness will cause the car’s dynamic balance to become unbalanced, causing the car’s high-speed steering wheel to shake. In the vehicle’s transmission system, the half shaft plays an important role and is the shaft that connects the drive wheels and the differential. The inner tie rod ends are generally connected to each other through side gears and splines, and the outer tie rod ends are connected to the wheel hub and flange. The structure of the automobile drive wheel is determined by the structural form of the half shaft. According to the different stress conditions of the half shaft, it can be divided into semi-floating half shaft and fully floating half shaft. It can be seen that the automobile half shaft is the most important factor in the daily driving of the car. An important component, the safe driving of the car depends on the performance of the drive shaft. After long-term torsional fatigue and impact, automobile half shafts are prone to bending, breakage, twisting, skewing, and spline tooth wear. The fractures of automobile half shafts usually have the following morphological types: 1.The spiral of the half-shaft shaft is broken; 2. Mixed cracks and fractures appear in the half-shaft shaft; 3.The splines of the half-shaft are broken; 4.The half-shaft is blue Cracks appear on the disc, and may even fall off in severe cases; 5.Other morphological fractures and cracks in the half shaft.

Product description
HDAG oem -20 2-1 auto spare parts propeller half shaft cardan rear axle reinforced drive shaft for chevrolet niva vaz 2123 2121-21214 

 

Item Name          Auto or car CV JOINT,Universal Joint,CV JOINT INNER OUTER, DRIVE SHAFT, DRIVESHAFT,CV AXLE, JOINT SHAFT ASSEMBLY,CV AXLE JOINT SHAFT, HALF SHAFT, WHEEL BEARING HUB, WHEEL HUB BEARING, WHEEL BEARING
OEM/REF NO.              2 2  2 2 2   2 2  -20  21213 -2203012-1  
Car Model For lada UAZ 2206/3151/3303/3741/9 3741 236571  3160 3163 NIVA VAZ samara moskvich 2141 Tavria 1102 GRANTA LARGUS Vesta X-Ray Kalina PRIORA BA3 Granta Kalina Priora OKA VESTA  Gazelle Gazelle Gazel Gazon Kamaz Patriot 
POSITION RH/LH/Right/ Left/ Front/Rear
MOQ 150PCS
Quality/Product parameters OEM standard or Design as sample or drawing
Payment Terms T/T, L/C, Credit card, Cash
Product Guarantee 1 Year or 50,
TOYOTA :
TOYOTA :
TOYOTA : 4342
TOYOTA : 4342
TOYOTA : 4342R20
TOYOTA : 4346R30
TOYOTA : 4346S50
TOYOTA : 4346
TOYOTA : 4347S60
TOYOTA : 4347U90
TOYOTA :
TOYOTA :
TOYOTA : 434708Z033
TOYOTA : 434708Z037
NISSAN : 391J10
NISSAN : 391571JJ10
NISSAN : 39157117JJ10
NISSAN : 3910110JJ10
NISSAN : 391M615
NISSAN : 391Y10
NISSAN : 391M570
NISSAN : 391N215
NISSAN : 391571M311
NISSAN : 391571M915
NISSAN : 3910140Y10
NISSAN : 391014M570
NISSAN : 391014M575
NISSAN : 391014M771
NISSAN : 3910163Y10
NISSAN : 391016N215
MAZDA : G057155J210
NISSAN : 391J171
NISSAN : 391N275
NISSAN : 391J071
NISSAN : 391J915
NISSAN : 391E478
NISSAN : 391012J215
NISSAN : 391014N175
NISSAN : 391014N177
NISSAN : 391014N275
NISSAN : 391015J571
NISSAN : 391016J571
NISSAN : 391016J071
NISSAN : 391016J076
NISSAN : 391016J915
NISSAN : 39101AE415
NISSAN : 39101AU415
NISSAN : 39101AU416
NISSAN : 39101AW110
NISSAN : 39101CX116
NISSAN : 39101WF715
NISSAN : 39101WF716
391 391M10
TOYOTA : 4347Z035
TOYOTA : 434708Z039
374077/374078/374092/7837456/7839615/7837457 3920164Y10 G564-25-5, 8D0498103, 8D0498103A,3B0498103,43145711H  8D0498099A,8D 0571 15H,8D0498099C,8D 0571 15H 43420-20380 3748103A 86~88099 435711011 44105-78B
VAG :
6Q0498099E, 6Q0498099B, 6Q0498099EX 43403-6, 96564144
,96396134,512395
39211-3U  39211-BM726 FD50-25-40XA, FA60-25-40X, FA58-25-50X FA252560XA/FA557160X/FA5822510/FA5822510B/FD54-25-60XA/FD55-25-50XA
1K0498103C 8K0498099X,8K0498099,8K0498099D 17145711  171498UU507
NISSAN : 391V70A
NISSAN : 391013U505
NISSAN : 391014V01C
NISSAN : 391014V51A
NISSAN : 391014V70A
NISSAN : 392113U
96348790
391
VOLVO : 8111304
VOLVO : 86011
VOLVO : 9122833
VOLVO : 9163595
7L 0571 11D,95534995712,95534995710, 7L0498099CX,7L0498099AX 17145711J,171498099A 374403/374403/9201725 39211-7F 8K 0571 15C, 8K0498099B, 8K0498099BX 171498099B,171498099BX 96273760/96549104/96951692 392112F225 MAZDA : G5712510
MAZDA : G571550X
MAZDA : G571560X
MAZDA : G565715
OPEL : 374
VAUXHALL : 571
391
MAZDA : MD1922510
MAZDA : MD1922510A
MAZDA : MD192550X
MAZDA : MD257160XB
44014-SP0-
OPEL : 374048
OPEL : 374067
OPEL : 37408
OPEL : 374118
OPEL : 374148
OPEL : 374195
OPEL : 90125876
OPEL : 90157212
OPEL : 95718734
OPEL : 9317340
OPEL : 93173430
SAAB : 4242319
392114F425  MD20-25-60X
44305SE0J22/44306SE0G12/44305SE0G23/44305SE0G24/44305SE0J20 A6383342334 391KD0A
NISSAN : 391KD0A
NISSAN : 391019Y015
NISSAN : 39101CNY015
NISSAN : 39211CNHN50
HONDA : 44305S04J60
HONDA : 44305S0A960
HONDA : 44305S0AN60
HONDA : 44305S2H571
HONDA : 44305S2H050
HONDA : 44305S2H950
HONDA : 44305S2H951
HONDA : 44305S2HN50
HONDA : 44305S5AJ50
HONDA : 44305S5AJ60
HONDA : 44305S5AJ61
HONDA : 44305S5AJ62
HONDA : 44305S5C950
HONDA : 44305S5CN50
HONDA : 44305S5CN51
HONDA : 44305S7B950
HONDA : 44305S7C950
HONDA : 44305SOA960
HONDA : 44305SOAN60
HONDA : 44306S0A960
HONDA : 44306S0AN60
HONDA : 44306S2H571
HONDA : 44306S2H950
HONDA : 44306S2H951
HONDA : 44306S5AJ51
HONDA : 44306S5AJ61
HONDA : 44306S5AJ62
HONDA : 44306S5C951
HONDA : 44306S5C952
HONDA : 44306S7B950
HONDA : 44306S7C950
HONDA : 44306SOA960
HONDA : 44306SOAN60
49591-1F410 44305-SA5-000,44305-688-000,44306-689-601,44306-688-571,44305-688-571 4401720,4401727,8200169277,8200169281,8200169285,8200169288,8200196277,8200178624 39210-Y02G0
 326582
 FG02-25-500D
FG02-25-500E
FG02-25-600D
 FG02-25-600E
44014-SDC-A50,44014-SCA-E01,44014SDCA51, 9565719/3273.17/3273.18/3273.20/3273.21/3273.23/3273.24/3274.79/3274.80 44305-SB2-750,44305-SF4-J21,44306-SK7-571
44305-SA2-960
825716110,7700111918,8200064731, 39100ED005
39100ED00A
39101ED00A
39101ED005
GF09-25-50X,GP28-25-50XA/GD36-25-60X
44014-SWE-T00,44014-SWE-T01,44014-SWA-000,44014-SWA-571,44014-SXS-A00 3272.00/3272.20/3273.55/3273.64/95598120 44305-SB2-982,44306-SB0-571
44571-SH3-J01,44306-SB2-984
7701351572,7701351571,7701351484,7701351480,7701351479,7701349938,7701349880,7701349874
 
39100-JX00A
39211-CN000
GP34-25-60XD
44014-SDE-T00,44014SDCA00,44306SDETOOL 3272.06/3273.75 44305-SH3-961, 44306-SH3-571, 44305-SE0-000,44571-SH3-960,44011-SH3-G12,44305-SH3-961 8200264664,39100-0153R,39101-5451R,6001548720,8200690053,820571122 1N00-25-500 KIA : 0K558-25-50X
KIA : 0K558-25-60X
 44305-TL1-E00,44014TA0A00 3273.Y7
3272.S5
44571SL5N01 44571SS571 44571SS0030 44011SS571 44011SS0030 391014946R 39100-AX000
39211-AY125
39101-AX005
39100-AX005
39101-AX000
MAZDA : M 0571 1510
MAZDA : M 0571 1510A
MAZDA : M 0571 1500C
MAZDA : M 0571 1500D
MAZDA : M 0571 1600A
MAZDA : M 0571 1600B
MAZDA : MD0925500A
MAZDA : MD0925600A
44014-S9A-571,44014-SDC-A50,44014-S9A-571, 44014-SCA-E00,44014-SCA-E01 3273.60/3273.62/3273.C7/3274.77/95606802/95646292/96184033 44305-SM4-983, 44571-SM4-A01, 44571-SL5-N01,44571-SV4-951,44011-SS0-930, 77,013,524,157,701,300,000 39210-F4125 MAZDA : G064-25-500
MAZDA : G064-25-600
MAZDA : G564-25-500A
MAZDA : G564-25-600A
MAZDA : G564-25-60X
MAZDA : GR01-25-500
MAZDA : GR01-25-50X
MAZDA : GR01-25-600
MAZDA : GR01-25-60X
MAZDA : GU01-25-500
MAZDA : GU01-25-50XA
MAZDA : GU01-25-50XC
MAZDA : GU01-25-600
MAZDA : GU01-25-60XA
MAZDA : GU01-25-60XD
44305-SAA-E00 9566722380/1495545080/1496138080/9567582280 44571-S07-000,44571SR3J01,44571SR3J02 299341X2 39100-1KA5B GG06-25-50XC
HONDA : 44014-SDC-A00
HONDA : 44014-SNG-000
HONDA : 44305-SDC-A00
HONDA : 44305-SEA-000
HONDA : 44305-SNG-571
HONDA : 44306-SDC-A01
HONDA : 44306-SDE-T00
HONDA : 44306-SEA-000
HONDA : 44306-SNG-571
1495537080;1495541080;9566722180,9566722180 44571SR3J03/44571SR3J53/44571ST7N00/44011S07000/44305SF1G10/44011ST3E00/44571-S07-950/44571-ST3-E50 9109186,775712978,775712980,775712998,775712999

 

NISSAN : 39100JA571
NISSAN : 39100JD24B
NISSAN : 39100JD52B
NISSAN : 39101JD24B
NISSAN : 39101JD52B
NISSAN : 39211JA00A
NISSAN : 39211JD22B
NISSAN : C9211JA00A
NISSAN : C9211JD22B
NISSAN : C92AAJA00A
NISSAN : C92AAJD22B
NISSAN : C9B11JA00A
NISSAN : C9BAAJA00A
MAZDA : CTA125500
MAZDA : FA8571500A
MAZDA : FA8571600B
MAZDA : FA8125600B
MAZDA : FA8225500A
MAZDA : FD8571500B
MAZDA : FD8571600A
MAZDA : FP0125500C
 44014-SDC-A00,44014-SDC-A00,44014-SDE-T00,44014-SNG-000,44306-SNG-571 3272-EX
3272-HY
3272-KW
3273-HQ
3273-KJ
43460-49125/43460-49165/43460-49315/43470-80013/43470-39545 1991909 NISSAN : 39100-ED100
NISSAN : 39100-ED105
NISSAN : 39100-ED305
NISSAN : 39100-ED805
NISSAN : 39101-ED105
NISSAN : 39101-ED305
NISSAN : 39101-ED805
NISSAN : 39211-ED100
NISSAN : C9211-EL10A
KIA : 0K2N122520
KIA : KK38825600
44014-S6D-E01 3272.3C 43410-12500,43410-57180 TDJ10571 39100-AX000/39100-ED100 HYUNDAI : 49500-25301
HYUNDAI : 49500-25302
HYUNDAI : 49500-25310
HYUNDAI : 49500-25311
HYUNDAI : 49500-25312
KIA : 49500-25301
KIA : 49500-25302
KIA : 49500-25310
KIA : 49500-25311
KIA : 49500-25312
44014-TA0-A00,44305-TA0-J00,44305-TA2-J00,44305-TL1-E00,44305-TL3-000,44306-TA0-J00 1481451080/3272.9C/3273.3Q 43460-19795 LAND ROVER : RTC6811
LAND ROVER : STC3046
4571-M7226
40011-M5626
39100-M7270
39101-M7270
39113-M7275
39112-M7225
4950624A00/MB297343/MB297873/MB526582/MB176160/MB176161/MB176865
44014-S9A-571,44014-SDE-T51, 44014-SMT-G01,44306-SEA-N00,44306S9AN00 9619947580 43410-57120/43460-19865/43420-12430 LAND ROVER : STC3051
LAND ROVER : TDJ00571
39101-1HS0A HYUNDAI : 49500-25200
HYUNDAI : 49500-25400
KIA : 49500-25200
KIA : 49500-25400
44306-SAA-000,44306-SFA-000,44306-SFB-000,44305-SAA-000 9619947580/9619947588/9619947688/9619947680 43410-12610, 43410-57130, 43410-12520,43410-0W270 LAND ROVER : LR060382
LAND ROVER : TDB500110
LAND ROVER : TDJ500030
39100CA000
39101-CA100
39211-CA100
39100-CA100
49508-22A00 49508-22E00
44014SD5A51 9619947580/9619947588/9619947688/9619947680 43430-0K571/43430-0K030/43460-80033 HONDA : 44305S74E00
HONDA : 44305S74E01
HONDA : 44305S74E51
ROVER : GCV1123
ROVER : TFB000070
39100-AX000
39211-AY125
39101-AX005
39100-AX005
39101-AX000
MB176872, MB297376, MB297377,MB526456,49500-2D002
44014-S91-571,44014S9A571,44305S9AN00,44305SCAG00 CITROEN : 3272QF
CITROEN : 3272TH
CITROEN : 3272WX
CITROEN : 3273QQ
CITROEN : 3273TT
CITROEN : 3273XR
DS : 3272QF
DS : 3272TH
DS : 3273QQ
DS : 3273TT
PEUGEOT : 3272QF
PEUGEOT : 3272TH
PEUGEOT : 3272WX
PEUGEOT : 3273QQ
PEUGEOT : 3273TT
PEUGEOT : 3273XR
43420-5710/43470-5711/43430-5711 GCV1194,TDJ100590 39211-CG000
39211-CG571
MB297438,MB297678,MB526831,MB297696,MB526473

   /* March 10, 2571 17:59:20 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

After-sales Service: Three Years
Condition: New
Color: OEM Standard
Certification: CE, ISO, ISO/Ts16949
Type: C.V. Joint
Application Brand: Nissan, Iveco, Toyota, Ford, Lada Mitsubishi FIAT Opel Peugeot Renault Citroen
Customization:
Available

|

Customized Request

axle shaft

Are there potential challenges or limitations to using specific axle shafts?

Using specific axle shafts in vehicles can come with challenges or limitations depending on various factors such as the design of the vehicle, the intended use, and the specific characteristics of the axle shafts. Here’s a detailed explanation of potential challenges or limitations associated with specific axle shafts:

  • Compatibility: One challenge is ensuring compatibility between the axle shafts and the vehicle’s drivetrain configuration, suspension system, and overall design. Axle shafts must be designed to fit the specific vehicle model and its corresponding drivetrain layout. Using incompatible axle shafts can lead to improper fitment, compromised performance, or even mechanical failures.
  • Strength and Durability: Depending on the vehicle’s weight, power output, and intended use, specific axle shafts may have limitations in terms of strength and durability. Axle shafts subjected to heavy loads, aggressive driving, or off-road conditions may require higher-strength materials or specialized designs to withstand the forces and torque applied to them. Using axle shafts that are not adequately designed for the vehicle’s demands can result in premature wear, bending, or breakage.
  • Performance Trade-offs: Different types of axle shafts offer different performance trade-offs. For example, solid axle shafts may provide durability and simplicity but can result in a harsher ride quality and limited independent wheel movement. On the other hand, CV (constant velocity) axle shafts offer smoother power delivery and greater wheel articulation but may have limitations in terms of torque capacity and durability under extreme conditions. It’s important to consider the specific requirements and priorities of the vehicle’s performance and select axle shafts accordingly.
  • Cost and Availability: Certain axle shafts, especially those designed for specialized applications or high-performance vehicles, may be more expensive or harder to source compared to standard axle shafts. Limited availability can pose challenges when it comes to replacement or upgrade options. Additionally, aftermarket axle shafts might not always meet the same quality standards as original equipment manufacturer (OEM) parts, which could impact their performance and reliability.
  • Modifications and Customization: Modifying or customizing axle shafts can introduce additional challenges. Altering axle shafts to accommodate different drivetrain configurations, wheel sizes, or suspension setups may require specialized knowledge, engineering expertise, and fabrication skills. Improper modifications can negatively affect the vehicle’s stability, handling, and safety.
  • Serviceability: Some specific axle shafts might have limited serviceability or require specialized tools or expertise for maintenance, repair, or replacement. This can impact the availability and cost of servicing the vehicle. It’s important to consider the long-term serviceability and support for specific axle shafts when selecting them for a vehicle.

It’s crucial to consult with knowledgeable professionals, such as automotive engineers or experienced mechanics, to ensure the appropriate selection and installation of axle shafts for a specific vehicle. They can provide valuable insights and guidance based on the vehicle’s requirements, intended use, and potential limitations associated with specific axle shafts.

In summary, potential challenges or limitations of using specific axle shafts include compatibility issues, limitations in strength and durability, performance trade-offs, cost and availability considerations, challenges related to modifications or customization, and serviceability concerns. A careful assessment of these factors is essential to ensure the optimal performance, safety, and reliability of the vehicle.

axle shaft

What are the advantages of using high-performance or heavy-duty axle shafts?

Using high-performance or heavy-duty axle shafts can offer several advantages in terms of strength, durability, and performance. These specialized axle shafts are designed to handle increased torque loads, provide improved power delivery, and withstand the demands of challenging applications. Here’s a detailed explanation of the advantages of using high-performance or heavy-duty axle shafts:

  • Increased Strength: High-performance or heavy-duty axle shafts are typically constructed from stronger materials, such as chromoly steel or alloy steel. These materials offer higher tensile and yield strength compared to standard axle shafts. The increased strength allows the shafts to handle higher torque loads without deformation or failure, providing enhanced reliability and durability.
  • Improved Power Delivery: High-performance axle shafts are designed to provide more efficient power delivery from the drivetrain to the wheels. The enhanced strength and rigidity of these shafts minimize power loss due to torsional flex, ensuring that a greater percentage of the torque generated by the engine reaches the wheels. This results in improved acceleration, better throttle response, and enhanced overall performance.
  • Enhanced Torsional Rigidity: Heavy-duty axle shafts are often engineered with increased torsional rigidity. This means they have reduced torsional flex or twisting under load. The improved torsional rigidity helps maintain consistent power transfer to the wheels, especially during high-torque situations or aggressive driving maneuvers. It contributes to better traction and stability, particularly in performance-oriented or off-road applications.
  • Increased Durability: High-performance or heavy-duty axle shafts are designed to withstand the demands of challenging applications. They are engineered to handle increased loads, higher rotational speeds, and more extreme operating conditions. By providing greater durability, these axle shafts can withstand off-road obstacles, heavy payloads, or aggressive driving without premature wear or failure.
  • Improved Off-Road Capability: High-performance or heavy-duty axle shafts are particularly beneficial in off-road applications. They can handle the additional stresses and forces encountered during off-road driving, such as uneven terrain, rock crawling, or high-speed desert runs. With increased strength and durability, these axle shafts reduce the risk of breakage, allowing off-road enthusiasts to explore challenging terrains with more confidence.
  • Support for Vehicle Modifications: High-performance or heavy-duty axle shafts are often used in vehicles with significant modifications, such as increased engine power, larger tires, or suspension upgrades. These axle shafts can accommodate the additional torque loads and provide the necessary strength and reliability to support the modified drivetrain and suspension components.

It’s important to note that the advantages of high-performance or heavy-duty axle shafts are most noticeable in applications where the vehicle is subjected to increased torque loads, extreme conditions, or performance-oriented driving. In everyday driving scenarios with standard vehicles, the benefits may be less pronounced.

When considering high-performance or heavy-duty axle shafts, it’s crucial to ensure compatibility with other drivetrain components, such as the differential, wheel hubs, and braking system. Additionally, professional installation by experienced technicians is recommended to ensure proper fitment and compatibility.

Overall, high-performance or heavy-duty axle shafts offer increased strength, improved power delivery, enhanced durability, and better performance characteristics, making them a valuable upgrade for specific applications where increased performance, reliability, and off-road capability are desired.

axle shaft

What are the components of an axle shaft assembly and their functions?

An axle shaft assembly consists of several components that work together to facilitate the transmission of power from the differential to the wheels. Each component plays a specific role in ensuring efficient power transfer and supporting the functionality of the axle shaft assembly. Here are the main components and their functions:

1. Axle Shaft:

The axle shaft itself is the main component of the assembly. It is a long, cylindrical shaft that connects the differential or transaxle to the wheels. The primary function of the axle shaft is to transmit rotational power from the differential to the wheels, enabling them to rotate and propelling the vehicle forward or backward.

2. Differential Side Gears or Output Shafts:

The axle shaft assembly is connected to the differential through side gears or output shafts. These are gear-like components that are part of the differential mechanism. The side gears or output shafts engage with the axle shafts, providing a solid mechanical connection. They allow the rotational force from the differential to be transmitted to the axle shafts, initiating power transfer to the wheels.

3. Constant Velocity (CV) Joints:

In many modern vehicles, especially those with front-wheel drive or independent suspension systems, the axle shaft assembly incorporates constant velocity (CV) joints. CV joints allow for smooth power transfer and accommodate changes in axle angle and length due to suspension movement and steering. They provide flexibility and reduce vibrations during power transmission. CV joints consist of inner and outer joints with ball bearings and protective boots filled with grease to maintain lubrication and prevent contamination.

4. Wheel Hubs:

At the outer ends of the axle shaft assembly, wheel hubs are attached. Wheel hubs serve as the connection points for the wheels. They provide a mounting surface for the wheels and ensure proper alignment and rotation. The axle shafts transmit the rotational power from the differential to the wheel hubs, causing the wheels to rotate. Wheel hubs often incorporate bearings to allow smooth rotation and reduce friction.

5. Bearings:

Bearings are crucial components within the axle shaft assembly. They support the rotating motion of the axle shafts and the wheel hubs. The bearings reduce friction and allow the axle shafts and wheel hubs to rotate freely. They are typically designed to withstand the forces and loads encountered during vehicle operation and contribute to smooth and efficient power transmission.

6. Seals and Retaining Devices:

To prevent the entry of contaminants and retain lubrication, seals are used in the axle shaft assembly. Seals are placed at various points along the assembly to protect the bearings, CV joints, and other critical components from dirt, moisture, and debris. Additionally, retaining devices such as circlips or snap rings are used to secure the axle shafts, CV joints, or bearings within their respective housings, ensuring proper alignment and preventing unintended disassembly.

These are the key components typically found in an axle shaft assembly. The combination of these components allows for effective power transmission, smooth rotation, support for the wheels, and protection of critical parts, ensuring the overall functionality and longevity of the axle shaft assembly.

China OEM CZPT OEM 2123-2201015-20 21213-2203012-1 Auto Spare Parts Propeller Half Shaft Cardan Rear Axle Reinforced Drive Shaft for Chevrolet Niva Vaz 2123 2121-21214   with high quality China OEM CZPT OEM 2123-2201015-20 21213-2203012-1 Auto Spare Parts Propeller Half Shaft Cardan Rear Axle Reinforced Drive Shaft for Chevrolet Niva Vaz 2123 2121-21214   with high quality
editor by CX 2024-01-04

China manufacturer Transmission Spline Propeller Worm Gear Shaft for Rice Transplanter drive shaft equipment

Product Description

Product Description

Product Parameters

Item Spur Gear Axle Shaft
Material 4140,4340,40Cr,42Crmo,42Crmo4,20Cr,20CrMnti, 20Crmo,35Crmo
OEM NO Customize
Certification ISO/TS16949
Test Requirement Magnetic Powder Test, Hardness Test, Dimension Test
Color Paint , Natural Finish ,Machining All Around
Material Aluminum: 5000series(5052…)/6000series(6061…)/7000series(7075…)
Steel: Carbon Steel,Middle Steel,Steel Alloy,etc.
Stainess Steel: 303/304/316,etc.
Copper/Brass/Bronze/Red Copper,etc.
Plastic:ABS,PP,PC,Nylon,Delrin(POM),Bakelite,etc.
Size According to Customer’s drawing or samples
Process CNC machining,Turning,Milling,Stamping,Grinding,Welding,Wire Injection,Cutting,etc.
Tolerance ≥+/-0.03mm
Surface Treatment (Sandblast)&(Hard)&(Color)Anodizing,(Chrome,Nickel,Zinc…)Plating,Painting,Powder Coating,Polishing,Blackened,Hardened,Lasering,Engraving,etc.
File Formats ProE,SolidWorks,UG,CAD,PDF(IGS,X-T,STP,STL)
Sample Available
Packing Spline protect cover ,Wood box ,Waterproof membrane; Or per customers’ requirements.

 

Our Advantages

Why Choose US ???

1. Equipment :

Our company boasts all necessary production equipment,
including Hydraulic press machines, Japanese CNC lathe (TAKISAWA), Korean gear hobbing machine (I SNT), gear shaping machine, machining center, CNC grinder, heat treatment line etc.

2. Processing precision:

We are a professional gear & gear shafts manufacturer. Our gears are around 6-7 grade in mass production.

3. Company:

We have 90 employees, including 10 technical staffs. Covering an area of 20000 square meters.

4. Certification :

Oue company has passed ISO 14001 and TS16949

5.Sample service :

We provide free sample for confirmation and customer bears the freight charges

6.OEM service :

Having our own factory and professional technicians,we welcome OEM orders as well.We can design and produce the specific product you need according to your detail information

 

Cooperation Partner

Company Profile

Our Featured Products

Material: Alloy Steel
Load: Drive Shaft
Axis Shape: Straight Shaft
Appearance Shape: Round
Rotation: Cw
Yield: 5, 000PCS / Month
Samples:
US$ 0/Piece
1 Piece(Min.Order)

|
Request Sample

Customization:
Available

|

Customized Request

air-compressor

How to tell if your driveshaft needs replacing

What is the cause of the unbalanced drive shaft? Unstable U-joint? Your car may make clicking noises while driving. If you can hear it from both sides, it might be time to hand it over to the mechanic. If you’re not sure, read on to learn more. Fortunately, there are many ways to tell if your driveshaft needs replacing.

unbalanced

An unbalanced driveshaft can be the source of strange noises and vibrations in your vehicle. To fix this problem, you should contact a professional. You can try a number of things to fix it, including welding and adjusting the weight. The following are the most common methods. In addition to the methods above, you can use standardized weights to balance the driveshaft. These standardized weights are attached to the shaft by welders.
An unbalanced drive shaft typically produces lateral vibrations per revolution. This type of vibration is usually caused by a damaged shaft, missing counterweights, or a foreign object stuck on the drive shaft. On the other hand, torsional vibrations occur twice per revolution, and they are caused by shaft phase shifts. Finally, critical speed vibration occurs when the RPM of the drive shaft exceeds its rated capacity. If you suspect a driveshaft problem, check the following:
Manually adjusting the imbalance of a drive shaft is not the easiest task. To avoid the difficulty of manual balancing, you can choose to use standardized weights. These weights are fixed on the outer circumference of the drive shaft. The operator can manually position the weight on the shaft with special tools, or use a robot. However, manual balancers have many disadvantages.

unstable

When the angular velocity of the output shaft is not constant, it is unstable. The angular velocity of the output shaft is 0.004 at ph = 29.5 and 1.9 at t = 1.9. The angular velocity of the intermediate shaft is not a problem. But when it’s unstable, the torque applied to it is too much for the machine. It might be a good idea to check the tension on the shaft.
An unstable drive shaft can cause a lot of noise and mechanical vibration. It can lead to premature shaft fatigue failure. CZPT studies the effect of shaft vibration on the rotor bearing system. They investigated the effect of flex coupling misalignment on the vibration of the rotor bearing system. They assume that the vibrational response has two components: x and y. However, this approach has limited application in many situations.
Experimental results show that the presence of cracks in the output shaft may mask the unbalanced excitation characteristics. For example, the presence of superharmonic peaks on the spectrum is characteristic of cracks. The presence of cracks in the output shaft masks unbalanced excitation characteristics that cannot be detected in the transient response of the input shaft. Figure 8 shows that the frequency of the rotor increases at critical speed and decreases as the shaft passes the natural frequency.

Unreliable

If you’re having trouble driving your car, chances are you’ve run into an unreliable driveshaft. This type of drivetrain can cause the wheels to stick or not turn at all, and also limit the overall control of the car. Whatever the reason, these issues should be resolved as soon as possible. Here are some symptoms to look for when diagnosing a driveshaft fault. Let’s take a closer look.
The first symptom you may notice is an unreliable drive shaft. You may feel vibrations, or hear noises under the vehicle. Depending on the cause, it could be a broken joint or a broken shaft. The good news is that driveshaft repairs are generally relatively inexpensive and take less time than a complete drivetrain replacement. If you’re not sure what to do, CZPT has a guide to replacing the U-connector.
One of the most common signs of an unreliable driveshaft is clanging and vibration. These sounds can be caused by worn bushings, loose U-joints, or damaged center bearings. This can cause severe vibration and noise. You can also feel these vibrations through the steering wheel or the floor. An unreliable driveshaft is a symptom of a bigger problem.
air-compressor

Unreliable U-joints

A car with an unreliable U-joint on the drive shaft can be dangerous. A bad u-joint can prevent the vehicle from driving properly and may even cause you trouble. Unreliable u-joints are cheap to replace and you should try getting parts from quality manufacturers. Unreliable U-joints can cause the car to vibrate in the chassis or gear lever. This is a sure sign that your car has been neglected in maintenance.
Replacing a U-joint is not a complicated task, but it requires special tools and a lot of elbow grease. If you don’t have the right tools, or you’re unfamiliar with mechanical terminology, it’s best to seek the help of a mechanic. A professional mechanic will be able to accurately assess the problem and propose an appropriate solution. But if you don’t feel confident enough, you can replace your own U-connector by following a few simple steps.
To ensure the vehicle’s driveshaft is not damaged, check the U-joint for wear and lubrication. If the U-joint is worn, the metal parts are likely to rub against each other, causing wear. The sooner a problem is diagnosed, the faster it can be resolved. Also, the longer you wait, the more you lose on repairs.

damaged drive shaft

The driveshaft is the part of the vehicle that connects the wheels. If the driveshaft is damaged, the wheels may stop turning and the vehicle may slow down or stop moving completely. It bears the weight of the car itself as well as the load on the road. So even a slight bend or break in the drive shaft can have dire consequences. Even a piece of loose metal can become a lethal missile if dropped from a vehicle.
If you hear a screeching noise or growl from your vehicle when shifting gears, your driveshaft may be damaged. When this happens, damage to the u-joint and excessive slack in the drive shaft can result. These conditions can further damage the drivetrain, including the front half. You should replace the driveshaft as soon as you notice any symptoms. After replacing the driveshaft, you can start looking for signs of wear.
A knocking sound is a sign of damage to the drive shaft. If you hear this sound while driving, it may be due to worn couplings, damaged propshaft bearings, or damaged U-joints. In some cases, the knocking noise can even be caused by a damaged U-joint. When this happens, you may need to replace the entire driveshaft, requiring a new one.
air-compressor

Maintenance fees

The cost of repairing a driveshaft varies widely, depending on the type and cause of the problem. A new driveshaft costs between $300 and $1,300, including labor. Repairing a damaged driveshaft can cost anywhere from $200 to $300, depending on the time required and the type of parts required. Symptoms of a damaged driveshaft include unresponsiveness, vibration, chassis noise and a stationary car.
The first thing to consider when estimating the cost of repairing a driveshaft is the type of vehicle you have. Some vehicles have more than one, and the parts used to make them may not be compatible with other cars. Even if the same car has two driveshafts, the damaged ones will cost more. Fortunately, many auto repair shops offer free quotes to repair damaged driveshafts, but be aware that such work can be complicated and expensive.

China manufacturer Transmission Spline Propeller Worm Gear Shaft for Rice Transplanter   drive shaft equipment	China manufacturer Transmission Spline Propeller Worm Gear Shaft for Rice Transplanter   drive shaft equipment
editor by CX 2023-05-30

China manufacturer 5019616AA for Jeep Grand Cherokee 02-03 Propeller Shaft Factory Manufacturer Prop Shaft drive shaft axle

Product Description

As a professional manufacturer for propeller shaft, we have +8AA 938-139 530 0571 1AB Application for JEEP Grand Cherokee 02-03 Material SS430/45# steel  Balancing Standrad G16, 3200rpm Warranty One Year

For some items, we have stock, small order (+3000USD) is welcome.

 

The following items are some of propeller shafts, If you need more information, pls contact us for ASAP.
 

for JEEP PROPELLER SHAFT

OEM

Application

OEM

Application
65-9312 for JEEP Cherokee 01 52853651AF for JEEP Grand Cherokee 11-12
52123612AD for JEEP Cherokee 14-18 5257197AC for JEEP Grand Cherokee 4.0L 99-01
65-9820 for JEEP Cherokee 84-86 5257198AD for JEEP Grand Cherokee 4.7L 99-02
530 0571 2AC for JEEP Cherokee 87-01 65-9773 for JEEP Grand cherokee 93-95
65-9738 for JEEP Cherokee 88 65-9771 for JEEP Grand cherokee 95
530 0571 3AC for JEEP Cherokee 89-00 65-9769 for JEEP Grand Cherokee 96
65-9669 for JEEP Cherokee 90-94 65-9762 for JEEP Grand cherokee 96-97
65-9764 for JEEP Cherokee 90-98 65-9761 for JEEP Grand cherokee 96-97
65-9776 for JEEP Cherokee 95-98 65-9779 for JEEP Grand cherokee 96-98
5215716AC for JEEP Commander 06-09 5215713AA for JEEP Grand Cherokee 99-03
52853006AB for JEEP Commander 06-10 52111597AA for JEEP Liberty 02-04
52853431AA for JEEP Commander 07-10 52111596AA for JEEP Liberty 02-07
21-001D for JEEP Commander 07-10 946-386 for JEEP Liberty 04-07
21-001D for JEEP Commander 07-10 52853442AE for JEEP Liberty 08-12
65-3002 for JEEP Compass 08-16 65-9751 for JEEP Wagoneer 71-79
65-9781 for JEEP Grand cherokee 02-03 52853321AC for JEEP CZPT 07-11
52105884AA for JEEP Grand cherokee 02-04 52853329AC for JEEP CZPT 07-11
5215718AE for JEEP Grand Cherokee 05-06 52853330AC for JEEP CZPT 07-11
5215710AF for JEEP Grand cherokee 05-07 52853319AC for JEEP CZPT 07-18
5215718AE for JEEP Grand Cherokee 05-10 52123557AA for JEEP CZPT 12-14
52853432AA for JEEP Grand Cherokee 07-10 52123551AA for JEEP CZPT 12-17
52123514AD for JEEP Grand Cherokee 11 52123555AA for JEEP CZPT 12-18
52123627A for JEEP Grand Cherokee 11 CVJ014BK for JEEP CZPT 12-18
936-085 for JEEP CZPT 97-06 530571 for JEEP CZPT 87-93
65-9315 for JEEP CZPT 98-02 52098220 for JEEP CZPT 94-95
65-9316 for JEEP CZPT 98-02 65-9765 for JEEP CZPT 97

 

After-sales Service: 1 Year
Condition: New
Color: Black
Certification: ISO, IATF
Type: Propeller Shaft/Drive Shaft
Application Brand: Jeep
Samples:
US$ 300/Piece
1 Piece(Min.Order)

|
Request Sample

Customization:
Available

|

Customized Request

air-compressor

Different parts of the drive shaft

The driveshaft is the flexible rod that transmits torque between the transmission and the differential. The term drive shaft may also refer to a cardan shaft, a transmission shaft or a propeller shaft. Parts of the drive shaft are varied and include:
The driveshaft is a flexible rod that transmits torque from the transmission to the differential

When the driveshaft in your car starts to fail, you should seek professional help as soon as possible to fix the problem. A damaged driveshaft can often be heard. This noise sounds like “tak tak” and is usually more pronounced during sharp turns. However, if you can’t hear the noise while driving, you can check the condition of the car yourself.
The drive shaft is an important part of the automobile transmission system. It transfers torque from the transmission to the differential, which then transfers it to the wheels. The system is complex, but still critical to the proper functioning of the car. It is the flexible rod that connects all other parts of the drivetrain. The driveshaft is the most important part of the drivetrain, and understanding its function will make it easier for you to properly maintain your car.
Driveshafts are used in different vehicles, including front-wheel drive, four-wheel drive, and front-engine rear-wheel drive. Drive shafts are also used in motorcycles, locomotives and ships. Common front-engine, rear-wheel drive vehicle configurations are shown below. The type of tube used depends on the size, speed and strength of the drive shaft.
The output shaft is also supported by the output link, which has two identical supports. The upper part of the drive module supports a large tapered roller bearing, while the opposite flange end is supported by a parallel roller bearing. This ensures that the torque transfer between the differentials is efficient. If you want to learn more about car differentials, read this article.

It is also known as cardan shaft, propeller shaft or drive shaft

A propshaft or propshaft is a mechanical component that transmits rotation or torque from an engine or transmission to the front or rear wheels of a vehicle. Because the axes are not directly connected to each other, it must allow relative motion. Because of its role in propelling the vehicle, it is important to understand the components of the driveshaft. Here are some common types.
Isokinetic Joint: This type of joint guarantees that the output speed is the same as the input speed. To achieve this, it must be mounted back-to-back on a plane that bisects the drive angle. Then mount the two gimbal joints back-to-back and adjust their relative positions so that the velocity changes at one joint are offset by the other joint.
Driveshaft: The driveshaft is the transverse shaft that transmits power to the front wheels. Driveshaft: The driveshaft connects the rear differential to the transmission. The shaft is part of a drive shaft assembly that includes a drive shaft, a slip joint, and a universal joint. This shaft provides rotational torque to the drive shaft.
Dual Cardan Joints: This type of driveshaft uses two cardan joints mounted back-to-back. The center yoke replaces the intermediate shaft. For the duplex universal joint to work properly, the angle between the input shaft and the output shaft must be equal. Once aligned, the two axes will operate as CV joints. An improved version of the dual gimbal is the Thompson coupling, which offers slightly more efficiency at the cost of added complexity.
air-compressor

It transmits torque at different angles between driveline components

A vehicle’s driveline consists of various components that transmit power from the engine to the wheels. This includes axles, propshafts, CV joints and differentials. Together, these components transmit torque at different angles between driveline components. A car’s powertrain can only function properly if all its components work in harmony. Without these components, power from the engine would stop at the transmission, which is not the case with a car.
The CV driveshaft design provides smoother operation at higher operating angles and extends differential and transfer case life. The assembly’s central pivot point intersects the joint angle and transmits smooth rotational power and surface speed through the drivetrain. In some cases, the C.V. “U” connector. Drive shafts are not the best choice because the joint angles of the “U” joints are often substantially unequal and can cause torsional vibration.
Driveshafts also have different names, including driveshafts. A car’s driveshaft transfers torque from the transmission to the differential, which is then distributed to other driveline components. A power take-off (PTO) shaft is similar to a prop shaft. They transmit mechanical power to connected components. They are critical to the performance of any car. If any of these components are damaged, the entire drivetrain will not function properly.
A car’s powertrain can be complex and difficult to maintain. Adding vibration to the drivetrain can cause premature wear and shorten overall life. This driveshaft tip focuses on driveshaft assembly, operation, and maintenance, and how to troubleshoot any problems that may arise. Adding proper solutions to pain points can extend the life of the driveshaft. If you’re in the market for a new or used car, be sure to read this article.

it consists of several parts

“It consists of several parts” is one of seven small prints. This word consists of 10 letters and is one of the hardest words to say. However, it can be explained simply by comparing it to a cow’s kidney. The cocoa bean has several parts, and the inside of the cocoa bean before bursting has distinct lines. This article will discuss the different parts of the cocoa bean and provide a fun way to learn more about the word.
air-compressor

Replacement is expensive

Replacing a car’s driveshaft can be an expensive affair, and it’s not the only part that needs servicing. A damaged drive shaft can also cause other problems. This is why getting estimates from different repair shops is essential. Often, a simple repair is cheaper than replacing the entire unit. Listed below are some tips for saving money when replacing a driveshaft. Listed below are some of the costs associated with repairs:
First, learn how to determine if your vehicle needs a driveshaft replacement. Damaged driveshaft components can cause intermittent or lack of power. Additionally, improperly installed or assembled driveshaft components can cause problems with the daily operation of the car. Whenever you suspect that your car needs a driveshaft repair, seek professional advice. A professional mechanic will have the knowledge and experience needed to properly solve the problem.
Second, know which parts need servicing. Check the u-joint bushing. They should be free of crumbs and not cracked. Also, check the center support bearing. If this part is damaged, the entire drive shaft needs to be replaced. Finally, know which parts to replace. The maintenance cost of the drive shaft is significantly lower than the maintenance cost. Finally, determine if the repaired driveshaft is suitable for your vehicle.
If you suspect your driveshaft needs service, make an appointment with a repair shop as soon as possible. If you are experiencing vibration and rough riding, driveshaft repairs may be the best way to prevent costly repairs in the future. Also, if your car is experiencing unusual noise and vibration, a driveshaft repair may be a quick and easy solution. If you don’t know how to diagnose a problem with your car, you can take it to a mechanic for an appointment and a quote.

China manufacturer 5019616AA for Jeep Grand Cherokee 02-03 Propeller Shaft Factory Manufacturer Prop Shaft   drive shaft axle	China manufacturer 5019616AA for Jeep Grand Cherokee 02-03 Propeller Shaft Factory Manufacturer Prop Shaft   drive shaft axle
editor by CX 2023-05-25

China factory High Quality Auto Parts Transmission Cardan Shaft Propeller Driveshaft custom drive shaft

Product Description

 

HangZhou Yuantuo Auto Parts Manufacturing Co., Ltd was founded in 1990,which is a company specialized in production and sales of rubber parts such as center support bearing,wiper blade and torque rod bush in China.It is located in the beautiful and rich city HangZhou with a very convenient transportation near ZheJiang Kowloon Railway at the east and near National Road 106 and 308.And it covers an area of 30,000 square meters.

It continually introduces new advanced equipment and production process to enhance core competence and reduce production cost. Our products cover more than 100 models,We all along stick to the belief of quality first and customer orientation. Now our products have been exported to many countries, such as USA, Russia, Mexico, Italy, Germany, Iran, Egypt, Dubai, Malaysia, Brazil, Peru, Nigeria, Pakistan, India etc. Strict quality control and perfect after-sales service make our products widely welcomed in domestic and overseas markets.

YTK as a global manufacture specialized in auto wiper blade,our company has been ahead of the industry advanced level in rubber srtip technology after more tan 10 years of continuous development and technolgical inovation.And we are always pursing “cost-effective product ” and provide the cutstomers with safe and high quality wiper as the core idea of our company.We laid a CZPT foundation for cooperation by continuous innowation of patend products.Our products cover a compleat range of models and non-standard products could be cus-tomized.Our company always sticks to the service  objective of keeping the customers satisfied .Hope that YTK could have common development and share succession to create a beautiful future together with you .

 

 

 

YOU COULD GET (Cooperation with us):

1 More than 360 types of models,expand your product catalog.
2 More better price than the trading company.
3 Support mould development help you CZPT the market opportunity.
4 Stock a lot of product mold, save the cost of developing mold for you.
5 Fast delivery!
6. Production capacity: 60,000-80,000 PCS/ month.

FAQ

 

Q1. What is your terms of packing?

      Generally, we pack our goods in neutral  boxes and brown cartons or as your demand.
       If you have legally registered patent,we can pack the goods in your branded boxes after getting your authorization letters.

 

Q2. What is your terms of delivery?

       EXW, FOB, CIF, CFR

 

Q3. How about your delivery time?

      Generally, it will take 10 to 30 days after receiving your advance payment.
      The specific delivery time depends on the items and the quantity of your order.

Condition: New
Color: Black
Certification: ISO
Material: Rubber
Transport Package: as Your Demand
Trademark: YTK
Samples:
US$ 0.1/Piece
1 Piece(Min.Order)

|
Request Sample

Customization:
Available

|

Customized Request

air-compressor
hollow drive shaft

Hollow driveshafts have many benefits. They are light and reduce the overall weight of the vehicle. The largest manufacturer of these components in the world is CZPT. They also offer lightweight solutions for various applications, such as high-performance axles. CZPT driveshafts are manufactured using state-of-the-art technology. They offer excellent quality at competitive prices.
The inner diameter of the hollow shaft reduces the magnitude of the internal forces, thereby reducing the amount of torque transmitted. Unlike solid shafts, hollow shafts are getting stronger. The material inside the hollow shaft is slightly lighter, which further reduces its weight and overall torque. However, this also increases its drag at high speeds. This means that in many applications hollow driveshafts are not as efficient as solid driveshafts.
A conventional hollow drive shaft consists of a first rod 14 and a second rod 14 on both sides. The first rod is connected with the second rod, and the second rod extends in the rotation direction. The two rods are then friction welded to the central area of ​​the hollow shaft. The frictional heat generated during the relative rotation helps to connect the two parts. Hollow drive shafts can be used in internal combustion engines and environmentally-friendly vehicles.
The main advantage of a hollow driveshaft is weight reduction. The splines of the hollow drive shaft can be designed to be smaller than the outside diameter of the hollow shaft, which can significantly reduce weight. Hollow shafts are also less likely to jam compared to solid shafts. Hollow driveshafts are expected to eventually occupy the world market for automotive driveshafts. Its advantages include fuel efficiency and greater flexibility compared to solid prop shafts.

Cardan shaft

Cardan shafts are a popular choice in industrial machinery. They are used to transmit power from one machine to another and are available in a variety of sizes and shapes. They are available in a variety of materials, including steel, copper, and aluminum. If you plan to install one of these shafts, it is important to know the different types of Cardan shafts available. To find the best option, browse the catalog.
Telescopic or “Cardan” prop shafts, also known as U-joints, are ideal for efficient torque transfer between the drive and output system. They are efficient, lightweight, and energy-efficient. They employ advanced methods, including finite element modeling (FEM), to ensure maximum performance, weight, and efficiency. Additionally, the Cardan shaft has an adjustable length for easy repositioning.
Another popular choice for driveshafts is the Cardan shaft, also known as a driveshaft. The purpose of the driveshaft is to transfer torque from the engine to the wheels. They are typically used in high-performance car engines. Some types are made of brass, iron, or steel and have unique surface designs. Cardan shafts are available in inclined and parallel configurations.
Single Cardan shafts are a common replacement for standard Cardan shafts, but if you are looking for dual Cardan shafts for your vehicle, you will want to choose the 1310 series. This type is great for lifted jeeps and requires a CV-compatible transfer case. Some even require axle spacers. The dual Cardan shafts are also designed for lifts, which means it’s a good choice for raising and lowering jeeps.
air-compressor

universal joint

Cardan joints are a good choice for drive shafts when operating at a constant speed. Their design allows a constant angular velocity ratio between the input and output shafts. Depending on the application, the recommended speed limit may vary depending on the operating angle, transmission power, and application. These recommendations must be based on pressure. The maximum permissible speed of the drive shaft is determined by determining the angular acceleration.
Because gimbal joints don’t require grease, they can last a long time but eventually fail. If they are poorly lubricated or dry, they can cause metal-to-metal contact. The same is true for U-joints that do not have oil filling capability. While they have a long lifespan, it can be difficult to spot warning signs that could indicate impending joint failure. To avoid this, check the drive shaft regularly.
U-joints should not exceed seventy percent of their lateral critical velocity. However, if this speed is exceeded, the part will experience unacceptable vibration, reducing its useful life. To determine the best U-joint for your application, please contact your universal joint supplier. Typically, lower speeds do not require balancing. In these cases, you should consider using a larger pitch diameter to reduce axial force.
To minimize the angular velocity and torque of the output shaft, the two joints must be in phase. Therefore, the output shaft angular displacement does not completely follow the input shaft. Instead, it will lead or lag. Figure 3 illustrates the angular velocity variation and peak displacement lead of the gimbal. The ratios are shown below. The correct torque for this application is 1360 in-Ibs.

Refurbished drive shaft

Refurbished driveshafts are a good choice for a number of reasons. They are cheaper than brand new alternatives and generally just as reliable. Driveshafts are essential to the function of any car, truck, or bus. These parts are made of hollow metal tubes. While this helps reduce weight and expense, it is vulnerable to external influences. If this happens, it may crack or bend. If the shaft suffers this type of damage, it can cause serious damage to the transmission.
A car’s driveshaft is a critical component that transmits torque from the engine to the wheels. A1 Drive Shaft is a global supplier of automotive driveshafts and related components. Their factory has the capability to refurbish and repair almost any make or model of driveshafts. Refurbished driveshafts are available for every make and model of vehicle. They can be found on the market for a variety of vehicles, including passenger cars, trucks, vans, and SUVs.
Unusual noises indicate that your driveshaft needs to be replaced. Worn U-joints and bushings can cause excessive vibration. These components cause wear on other parts of the drivetrain. If you notice any of these symptoms, please take your vehicle to the AAMCO Bay Area Center for a thorough inspection. If you suspect damage to the driveshaft, don’t wait another minute – it can be very dangerous.
air-compressor

The cost of replacing the drive shaft

The cost of replacing a driveshaft varies, but on average, this repair costs between $200 and $1,500. While this price may vary by vehicle, the cost of parts and labor is generally equal. If you do the repair yourself, you should know how much the parts and labor will cost before you start work. Some parts can be more expensive than others, so it’s a good idea to compare the cost of several locations before deciding where to go.
If you notice any of these symptoms, you should seek a repair shop immediately. If you are still not sure if the driveshaft is damaged, do not drive the car any distance until it is repaired. Symptoms to look for include lack of power, difficulty moving the car, squeaking, clanking, or vibrating when the vehicle is moving.
Parts used in drive shafts include center support bearings, slip joints, and U-joints. The price of the driveshaft varies by vehicle and may vary by model of the same year. Also, different types of driveshafts require different repair methods and are much more expensive. Overall, though, a driveshaft replacement costs between $300 and $1,300. The process may take about an hour, depending on the vehicle model.
Several factors can lead to the need to replace the drive shaft, including bearing corrosion, damaged seals, or other components. In some cases, the U-joint indicates that the drive shaft needs to be replaced. Even if the bearings and u-joints are in good condition, they will eventually break and require the replacement of the drive shaft. However, these parts are not cheap, and if a damaged driveshaft is a symptom of a bigger problem, you should take the time to replace the shaft.

China factory High Quality Auto Parts Transmission Cardan Shaft Propeller Driveshaft   custom drive shaft	China factory High Quality Auto Parts Transmission Cardan Shaft Propeller Driveshaft   custom drive shaft
editor by CX 2023-05-16

China supplier Swp-G Transmission Cardan Shaft Propeller Drive Shafts manufacturer

Item Description

SWP G Type Cardan Shaft(JB/T3241-1991)

Cardan shaft is commonly utilised in rolling mill, punch, straightener, crusher, ship generate,paper producing products, typical equipment, drinking water pump tools,examination bench and other mechanical programs.

·Mark instance:
Tactical diameter D=250mm,Installation duration L=585mm,G kind cardan shaft
SWP250G×585 Coupling JB/T3241-91

♦Product Display

·SWP G Type Cardan Shaft Simple Parameter And Main Dimension(JB/T3241-1991)

Type Tactical diameter
D
mm
 
Nominal torque
Tn
kN·m
Fatique torque Tf
kN·m
Axis
angle
β
(°)
Stretch
length
S
mm
Measurement(mm) Rotary
inertia
kg·mtwo
 
Mass
kg
Lmin D1
 
Dtwo
js11
Dthree
H7
E E1 B×h hone Lone n-d
SWP225G 225 18 8 ≤5 forty 435 275 248 a hundred thirty five fifteen five 32×18 9 68 ten-fifteen .331 60
SWP250G 250 25 11.2 ≤5 40 515 305 275 a hundred and fifty 15 5 40×25 twelve.5 eighty 10-17 .624 ninety seven
SWP285G 285 35.5 sixteen ≤5 forty 565 565 314 170 eighteen seven 40×30 15 ninety 10-19 one.182 120
SWP315G 315 fifty 25 ≤5 40 620 620 328 185 18 seven 40×30 fifteen a hundred ten-19 two.290 a hundred and seventy
SWP350G 350 71 35.5 ≤5 40 715 715 370 210 22 8 50×32 16 108 ten-21 3.793 256

·Note:L is the size of installation,like the benefit of S/Z shrinkage.

♦Other Merchandise Listing

Transmission Machinery 
Elements Title
Model
Universal Coupling WS,WSD,WSP
Cardan Shaft SWC,SWP,SWZ
Tooth Coupling CL,CLZ,GCLD,GIICL,
GICL,NGCL,GGCL,GCLK
Disc Coupling JMI,JMIJ,JMII,JMIIJ
High Flexible Coupling LM
Chain Coupling GL
Jaw Coupling LT
Grid Coupling JS

♦Our Company
Our business provides distinct varieties of merchandise. Substantial high quality and reasonable value. We stick to the basic principle of “good quality 1st, support initial, steady enhancement and innovation to meet up with the clients” for the administration and “zero defect, zero problems” as the top quality goal. To perfect our services, we supply the products with excellent top quality at the sensible price.

Welcome to personalize goods from our manufacturing unit and remember to supply your design drawings or make contact with us if you need other specifications.

♦Our Services
1.Design Providers
Our design and style crew has experience in cardan shaft relating to merchandise design and development. If you have any requirements for your new solution or want to make additional enhancements, we are below to supply our assist.

2.Item Providers
raw components → Cutting → Forging →Rough machining →Shot blasting →Heat therapy →Testing →Fashioning →Cleaning→ Assembly→Packing→Shipping

three.Samples Process
We could build the sample according to your necessity and amend the sample constantly to meet up with your need.

four.Investigation & Development
We normally analysis the new wants of the industry and produce the new design when there is new automobiles in the market.

5.High quality Control
Each stage should be particular take a look at by Skilled Personnel in accordance to the standard of ISO9001 and TS16949.

FAQ
Q 1: Are you buying and selling firm or producer?
A: We are a professional company specializing in producing
different sequence of couplings.

Q 2:Can you do OEM?
Yes, we can. We can do OEM & ODM for all the consumers with tailored artworks of PDF or AI format.

Q 3:How prolonged is your delivery time?
Typically it is 20-thirty days if the goods are not in stock. It is in accordance to amount.

Q 4: Do you provide samples ? Is it free or extra ?
Yes, we could offer you the sample but not for free.In fact we have a very good price tag basic principle, when you make the bulk purchase then price of sample will be deducted.

Q 5: How prolonged is your guarantee?
A: Our Guarantee is 12 month below standard circumstance. 

Q 6: What is the MOQ?
A:Generally our MOQ is 1pcs.

Q 7: Do you have inspection techniques for coupling ?
A:100% self-inspection just before packing.

Q 8: Can I have a visit to your factory prior to the order? 
A: Certain,welcome to go to our manufacturing facility.

Q 9: What is actually your payment?
A:1) T/T. 2) L/C 

Speak to Us
Net: huadingcoupling
 
 
Add: No.1 HangZhou Highway,Chengnan park,HangZhou Metropolis,ZheJiang Province,China
 

 

Standard Or Nonstandard: Standard
Shaft Hole: as Required
Torque: as Required
Bore Diameter: as Required
Speed: as Required
Structure: Rigid
Samples:
US$ 500/Piece
1 Piece(Min.Order)

|
Request Sample

Customization:
Available

|

Customized Request